Kelley’s HP dockleveler provides automatic hydraulic operation with a single push-button activation and
a mechanically activated lip. The HP’s unique Gravity-Lip™ automatically extends the lip in a smooth,
quiet fashion as the dockleveler descends into the trailer.
Automatic hydraulic operation with single push-button activation.
|
|
4" diameter ramp cylinder mounted at front of ramp for maximum
strength and efficiency.
|
|
Hydraulic load-sensing system limits platform free fall to 3" or
less.
|
|
Automatic retracting legs for full-range free float, operator
adjustments are not required for below-dock operation.
|
|
Pre-wired electrical hook-up for easy installation.
|
|
Automatic lip extension with every cycle.
|
|
Easy clean pit design
|
|
Self-cleaning, lug-type lip hinge with lifetime warranty.
|
|
Fixed rear hinge, no pinch point.
|
|
Full operating range toe guards with OSHA-required yellow markings per
ANSI-Z535.
|
|
Integral maintenance strut and separate lip lock hold ramp and lip in
raised position for service or maintenance.
|
|
Patented Lambda deck beams optimize twist resistance and stress
distribution. Beams are robotically welded to deck.
|
|
60,000 lb. structural dock level support legs.
|
Model
|
25,000 lb. Capacity
|
30,000 lb. Capacity
|
35,000 lb. Capacity*
|
40,000 lb. Capacity
|
45,000 lb. Capacity*
|
50,000 lb. Capacity
|
HP6x6
|
1,430 lbs.
|
1,475 lbs.
|
1,555 lbs.
|
1,635 lbs.
|
1,715 lbs.
|
1,865 lbs.
|
HP6x8
|
1,720 lbs.
|
1,765 lbs.
|
1,845 lbs.
|
1,925 lbs.
|
2,005 lbs.
|
2,155 lbs.
|
HP6x10
|
2,330 lbs.
|
2,375 lbs.
|
2,480 lbs.
|
2,575 lbs.
|
2,670 lbs.
|
2,820 lbs.
|
HP6.5x6
|
1,515 lbs.
|
1,560 lbs.
|
1,645 lbs.
|
1,725 lbs.
|
1,810 lbs.
|
1,960 lbs.
|
HP6.5x8
|
1,813 lbs.
|
1,858 lbs.
|
1,945 lbs.
|
2,025 lbs.
|
2,105 lbs.
|
2,255 lbs.
|
HP6.5x10
|
2,445 lbs.
|
2,490 lbs.
|
2,600 lbs.
|
2,700 lbs.
|
2,800 lbs.
|
2,950 lbs.
|
HP7x6
|
1,600 lbs.
|
1,645 lbs.
|
1,730 lbs.
|
1,815 lbs.
|
1,900 lbs.
|
2,150 lbs.
|
HP7x8
|
1,905 lbs.
|
1,950 lbs.
|
2,040 lbs.
|
2,128 lbs.
|
2,215 lbs.
|
2,365 lbs.
|
HP7x10
|
2,560 lbs.
|
2,605 lbs.
|
2,725 lbs.
|
2,828 lbs.
|
2,930 lbs.
|
3,080 lbs.
|
*Reinforced
Consistent with our policy of continuing product improvement, we reserve the right to change these specifications without
notice or obligation.
Dockleveler rises when NEMA 4X shielded push-button is pushed and held. Gravity Lip automatically extends as deck section
descends into trailer bed. After loading or unloading is complete, dock attendant pushes button to activate hydraulic system
and raise dockleveler. Gravity Lip falls pendant and dockleveler is stored. In stored position, dockleveler is fully supported by
dock level support legs. Ramp may be lowered to fully supported below-dock level position, without extending lip,
to service low trucks in end-load situations.
6' and 8' long models - 24", 12" above dock to 12"
below.
|
|
10' long models - 27", 18" above dock to 9" below.
|
Unitized ramp with 50 KSI yield deck plate, 50 KSI yield beams and 55
KSI yield lip.
|
|
Self-cleaning, lug-type lip hinge with lifetime warranty.
|
|
Fully welded, easy-clean subframe design.
|
|
Fixed rear hinge provides 4" of side-to-side tilt without gap at
rear hinge.
|
|
Unitized pump/motor assembly.
|
|
Four-way tread plate on ramp and lip.
|
|
Control box dimensions 3" x 5" x 2 5/8".
|
Side and rear weatherseal.
|
|
Spacer kit for existing pits.
|
|
18" lip.
|
|
20" lip.
|
|
Minimum lip bend.
|
|
Curb angle sets.
|
|
Self-forming pans.
|
|
Foam-insulated ramp.
|
|
Spray-metalized ramp, lip and frame.
|